Quasar CM-3211 Series Installationsanleitung Seite 28
- Seite / 137
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation
17
5. Plug the Cat 5 cable into the camera’s Ethernet port and, if needed, plug the power terminal
block into the power terminals.
6. If applicable, wire the Alarm In, Alarm Out, Audio In, and Audio Out terminal blocks to
external devices. See Figure 6: CM-3211/4221 Camera Input/Output Connections.
7. If needed, connect the other end of the Cat 5 cable to the network and turn on the power
from the power supply.
Note:
Do not reassemble the camera’s inner cover and Mini-Dome cover until after
hardware configurations and lens adjustments are made.
5.6.3 Mounting the CM-3211/4221-01/11/11-I Outdoor Camera
1. Do one of the following:
For drilled wall or ceiling mounting:
a) Use a pointed pencil and the base plate as a template to mark the mounting surface
through the plate holes where the four screw holes will need to be drilled.
Caution:
Before marking and drilling the holes, ensure that the base plate alignment is
oriented correctly so that the required camera field of view can be achieved when
the system is assembled.
Figure 14: Base Plate Used as a Template to Mark Drilling Locations
b) In the marked locations, drill each hole using a drill-bit of a slightly smaller diameter
than the supplied screw anchors (molly-plug anchor). You want to achieve a snug
insertion so that the plug expansion holds firm after the screws are screwed in.
c) Fully insert the supplied anchors into drilled holes. You may need to tap them flush
with the wall using a finishing hammer.
• For installing on a 4S recessed electrical box:
a) Have a qualified installer (check your local electrical codes) rough-in the 4S recessed
electrical box and run the wires and power (if not PoE) through the wall/conduits to
the box location.
b) Ensure that the box is sufficiently sturdy (attach to the wall stud, ceiling joist, or
reinforced surface as needed) to securely hold the weight of the camera.
- Table of Contents 2
- Revision History 7
- 1 Document Information 8
- Disclaimer 9
- Document Conventions 9
- Document Information 10
- Minimizing EMI and RFI 11
- Site Preparation 11
- 2 Overview 12
- 2.1 Features 13
- 2.2 Package Contents 14
- Designation 15
- Description 15
- 3.4 Camera Connections 18
- 4 System Requirements 20
- 5 Installation 22
- Installation 24
- 5.5 Removing the Base Plate 25
- 5.6 Mounting Instructions 26
- 29
- 6.1 Introduction 31
- 6.2 Quick Start 31
- 6.3 Main Screen 32
- 6.4 Navigation Bar 32
- 6.5 Context Menu 33
- Figure 24: Security Window 36
- 7.2 Home Page 42
- 7.3 System-Related Settings 45
- 7.3.1 System 46
- 7.3.2 Security 47
- 7.3.2.1 User 48
- 7.3.2.2 HTTPS 49
- Figure 35: HTTPS Screen 50
- 7.3.2.3 IP Filter 53
- 7.3.2.4 IEEE 802.1X 54
- 7.3.3 Network 56
- 7.3.3.1 Basic 56
- Figure 44: QoS Screen 58
- 7.3.3.3 SNMP Settings 59
- 7.3.3.4 UPnP 61
- 7.3.4 DDNS 62
- 7.3.5 Mail 63
- 7.3.6 FTP 64
- 7.3.7 HTTP 65
- 7.3.8 Application 66
- 7.3.9 Motion Detection 70
- 7.3.11 Tampering 75
- 7.3.12 Storage Management 77
- 7.3.13 Recording 80
- 7.3.14 Schedule 81
- 7.3.15 File Location 82
- 7.3.16 View Information 83
- 7.3.16.1 Log File 83
- 7.3.16.2 User Information 84
- 7.3.16.3 Parameters 85
- 7.3.17 Factory Default 86
- 7.3.18 Software Version 87
- 7.3.19 Software Upgrade 87
- 7.3.20 Maintenance 89
- 7.4.1 Video Format 90
- 7.4.1.6 Video Rotate Type 99
- 7.4.1.7 GOV Settings 100
- 7.4.1.8 H.264 Profile 100
- 7.4.2 Video Compression 101
- 7.4.3 Video OCX Protocol 102
- 7.4.4 Video Frame Rate 103
- 7.4.5 Video Mask 104
- 7.4.6 Audio 105
- 7.5 Camera-Related Settings 106
- 7.5.1 Exposure 107
- Auto Iris 108
- Min Shutter Speed 108
- Auto Shutter – 108
- Min Shutter speed 108
- Shutter Speed Priority 109
- Manual Mode 109
- Fixed Shutter Speeds 109
- 7.5.2 White Balance 110
- 7.5.4 Backlight 112
- 7.5.5 Digital Zoom 112
- 7.5.6 IR Function 113
- 7.5.7 WDR Function 114
- 7.5.8 Noise Reduction 115
- 7.5.9 TV System 116
- 7.6 Logout 117
- 8 Appendices 118
- A.2. Device Search Software 122
- Device Search Software 124
- Figure 107: Schedule Screen 128
- A.4. Install UPnP Components 129
- Install UPnP Components 130
- A.8. Mounting Accessories 134
- Mounting Accessories 136
- Contacting DVTEL 137
Verwandte Produkte und Handbücher für Sicherheitskameras Quasar CM-3211 Series
(121 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern